# Holybro Pixhawk 4 Wiring Quickstart - Discontinued :::warning PX4 does not manufacture this (or any) autopilot. Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues. ::: This quick start guide shows how to power the [Pixhawk 4](/px4-user-guide/drone_parts/flight_controller/autopilot_pixhawk_standard/pixhawk4.md)® flight controller and connect its most important peripherals. ![](/files/HjGPJz2NnGD5xn4qqHlc) ## Wiring Chart Overview The image below shows how to connect the most important sensors and peripherals (except the motor and servo outputs). We'll go through each of these in detail in the following sections. ![Pixhawk 4 Wiring Overview](/files/0zDn6z3BKrI33MvCal3W) :::tip More information about available ports can be found here: [Pixhawk 4 > Connections](/px4-user-guide/drone_parts/flight_controller/autopilot_pixhawk_standard/pixhawk4.md#connectors). ::: ## Mount and Orient Controller *Pixhawk 4* should be mounted on the frame using vibration-damping foam pads (included in the kit). It should be positioned as close to your vehicle’s center of gravity as possible, oriented top-side up with the arrow pointing towards the front of the vehicle. ![](/files/3OhGFnQQPHfXK5A1llwb) :::note If the controller cannot be mounted in the recommended/default orientation (e.g. due to space constraints) you will need to configure the autopilot software with the orientation that you actually used: [Flight Controller Orientation](/px4-user-guide/config/flight_controller_orientation.md). ::: ## GPS + Compass + Buzzer + Safety Switch + LED Attach the provided GPS with integrated compass, safety switch, buzzer and LED to the **GPS MODULE** port. The GPS/Compass should be [mounted on the frame](/px4-user-guide/assembly/mount_gps_compass.md) as far away from other electronics as possible, with the direction marker towards the front of the vehicle (separating the compass from other electronics will reduce interference). ![Connect compass/GPS to Pixhawk 4](/files/TUSKbc3o0y97KFj2IIBH) :::note The GPS module's integrated safety switch is enabled *by default* (when enabled, PX4 will not let you arm the vehicle). To disable the safety press and hold the safety switch for 1 second. You can press the safety switch again to enable safety and disarm the vehicle (this can be useful if, for whatever reason, you are unable to disarm the vehicle from your remote control or ground station). ::: ## Power Connect the output of the *Power Management Board* (PM board) that comes with the kit to one of the **POWER** bricks of *Pixhawk 4* using a 6-wire cable. The PM input **2\~12S** will be connected to your LiPo battery. The connections of Power Management Board, including power supply and signal connections to the ESCs and servos, are explained in the table below. Note that the PM board does not supply power to the servos via + and - pins of **FMU PWM-OUT**. The image below shows the power management board provided with *Pixhawk 4*. ![Pixhawk 4 - Power Management Board](/files/PjMPQ4nyJx54yqWQkPTh) :::note If using a plane or rover, the 8 pin power (+) rail of **FMU PWM-OUT** will need to be separately powered in order to drive servos for rudders, elevons etc. To do this, the power rail needs to be connected to a BEC equipped ESC or a standalone 5V BEC or a 2S LiPo battery. Be careful with the voltage of servo you are going to use here. ::: | PIN\&Connector | Function | | -------------- | ----------------------------------------------------------------------------------------------------------- | | I/O PWM-IN | See note below for connection to *Pixhawk 4* | | M1 | I/O PWM OUT 1: connect signal wire to ESC of motor 1 here | | M2 | I/O PWM OUT 2: connect signal wire to ESC of motor 2 here | | M3 | I/O PWM OUT 3: connect signal wire to ESC of motor 3 here | | M4 | I/O PWM OUT 4: connect signal wire to ESC of motor 4 here | | M5 | I/O PWM OUT 5: connect signal wire to ESC of motor 5 here | | M6 | I/O PWM OUT 6: connect signal wire to ESC of motor 6 here | | M7 | I/O PWM OUT 7: connect signal wire to ESC of motor 7 here | | M8 | I/O PWM OUT 8: connect signal wire to ESC of motor 8 here | | FMU PWM-IN | See note below for connection to *Pixhawk 4* | | FMU PWM-OUT | If FMU PWM-IN is connected to *Pixhawk 4*, connect signal wires to ESC or signal, +, - wires to servos here | | CAP\&ADC-OUT | connect to CAP & ADC IN port of *Pixhawk 4* | | CAP\&ADC-IN | CAP\&ADC input: Pinouts are printed on the back side of the board | | B+ | connect to ESC B+ to power the ESC | | GND | connect to ESC Ground | | PWR1 | 5v output 3A, connect to *Pixhawk 4* POWER 1 | | PWR2 | 5v output 3A, connect to *Pixhawk 4* POWER 2 | | 2\~12S | Power Input, connect to 12S LiPo Battery | :::note Depending on your airframe type, refer to [Airframe Reference](/px4-user-guide/airframes/airframe_reference.md) to connect **I/O PWM OUT** and **FMU PWM OUT** ports of *Pixhawk 4* to PM board. **MAIN** outputs in PX4 firmware map to **I/O PWM OUT** port of *Pixhawk 4* whereas **AUX outputs** map to **FMU PWM OUT** of *Pixhawk 4*. For example, **MAIN1** maps to IO\_CH1 pin of **I/O PWM OUT** and **AUX1** maps to FMU\_CH1 pin of **FMU PWM OUT**. **FMU PWM-IN** of PM board is internally connected to **FMU PWM-OUT**. **I/O PWM-IN** of PM board is internally connected to **M1-8**. ::: The following table summarizes how to connect *Pixhawk 4*'s PWM OUT ports to PM board's PWM-IN ports, depending on the Airframe Reference. | Airframe Reference | Connection between *Pixhawk 4* --> PM board | | ------------------ | ------------------------------------------- | | **MAIN**: motor | I/O PWM OUT --> I/O PWM IN | | **MAIN**: servo | I/O PWM OUT --> FMU PWM IN | | **AUX**: motor | FMU PWM OUT --> I/O PWM IN | | **AUX**: servo | FMU PWM OUT --> FMU PWM IN | The pinout of *Pixhawk 4*’s power ports is shown below. The CURRENT signal should carry an analog voltage from 0-3.3V for 0-120A as default. The VOLTAGE signal should carry an analog voltage from 0-3.3V for 0-60V as default. The VCC lines have to offer at least 3A continuous and should default to 5.1V. A lower voltage of 5V is still acceptable, but discouraged. | Pin | Signal | Volt | | -------- | ------- | ----- | | 1(red) | VCC | +5V | | 2(black) | VCC | +5V | | 3(black) | CURRENT | +3.3V | | 4(black) | VOLTAGE | +3.3V | | 5(black) | GND | GND | | 6(black) | GND | GND | :::note Using the Power Module that comes with the kit you will need to configure the *Number of Cells* in the [Power Settings](https://docs.qgroundcontrol.com/master/en/SetupView/Power.html) but you won't need to calibrate the *voltage divider*. You will have to update the *voltage divider* if you are using any other power module (e.g. the one from the Pixracer). ::: ## Radio Control A remote control (RC) radio system is required if you want to *manually* control your vehicle (PX4 does not require a radio system for autonomous flight modes). You will need to [select a compatible transmitter/receiver](/px4-user-guide/getting_started/rc_transmitter_receiver.md) and then *bind* them so that they communicate (read the instructions that come with your specific transmitter/receiver). The instructions below show how to connect the different types of receivers to *Pixhawk 4*: * Spektrum/DSM or S.BUS receivers connect to the **DSM/SBUS RC** input. ![Pixhawk 4 - Radio port for Spektrum receivers](/files/b4rS8QBln2i1Us5gUcF8) * PPM receivers connect to the **PPM RC** input port. ![Pixhawk 4 - Radio port for PPM receivers](/files/2BU1dHHU0FlMruNTHVD5) * PPM and PWM receivers that have an *individual wire for each channel* must connect to the **PPM RC** port *via a PPM encoder* [like this one](http://www.getfpv.com/radios/radio-accessories/holybro-ppm-encoder-module.html) (PPM-Sum receivers use a single signal wire for all channels). For more information about selecting a radio system, receiver compatibility, and binding your transmitter/receiver pair, see: [Remote Control Transmitters & Receivers](/px4-user-guide/getting_started/rc_transmitter_receiver.md). ## Telemetry Radios (Optional) Telemetry radios may be used to communicate and control a vehicle in flight from a ground station (for example, you can direct the UAV to a particular position, or upload a new mission). The vehicle-based radio should be connected to the **TELEM1** port as shown below (if connected to this port, no further configuration is required). The other radio is connected to your ground station computer or mobile device (usually by USB). ![Pixhawk 4/Telemetry Radio](/files/RiNB6DxC3GufF0RdKWUm) ## SD Card (Optional) SD cards are highly recommended as they are needed to [log and analyse flight details](/px4-user-guide/getting_started/flight_reporting.md), to run missions, and to use UAVCAN-bus hardware. Insert the card (included in Pixhawk 4 kit) into *Pixhawk 4* as shown below. ![Pixhawk 4/SD Card](/files/uU8nrmxtsBxdHMe3YTdY) :::tip For more information see [Basic Concepts > SD Cards (Removable Memory)](/px4-user-guide/getting_started/px4_basic_concepts.md#sd-cards-removable-memory). ::: ## Motors Motors/servos are connected to the **I/O PWM OUT** (**MAIN**) and **FMU PWM OUT** (**AUX**) ports in the order specified for your vehicle in the [Airframe Reference](/px4-user-guide/airframes/airframe_reference.md). :::note This reference lists the output port to motor/servo mapping for all supported air and ground frames (if your frame is not listed in the reference then use a "generic" airframe of the correct type). ::: :::warning The mapping is not consistent across frames (e.g. you can't rely on the throttle being on the same output for all plane frames). Make sure to use the correct mapping for your vehicle. ::: ## Other Peripherals The wiring and configuration of optional/less common components is covered within the topics for individual [peripherals](/px4-user-guide/drone_parts/peripherals.md). ## Pinouts [Pixhawk 4 Pinouts](https://holybro.com/manual/Pixhawk4-Pinouts.pdf) (Holybro) ## Configuration General configuration information is covered in: [Autopilot Configuration](/px4-user-guide/config.md). QuadPlane specific configuration is covered here: [QuadPlane VTOL Configuration](/px4-user-guide/airframes/frames_vtol/config_vtol/vtol_quad_configuration.md) ## Further information * [Pixhawk 4](/px4-user-guide/drone_parts/flight_controller/autopilot_pixhawk_standard/pixhawk4.md) (Overview page) * [Pixhawk 4 Technical Data Sheet](https://github.com/PX4/PX4-user_guide/raw/main/assets/flight_controller/pixhawk4/pixhawk4_technical_data_sheet.pdf) * [Pixhawk 4 Pinouts](https://holybro.com/manual/Pixhawk4-Pinouts.pdf) (Holybro) * [Pixhawk 4 Quick Start Guide (Holybro)](https://holybro.com/manual/Pixhawk4-quickstartguide.pdf) --- # Agent Instructions: Querying This Documentation If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question. Perform an HTTP GET request on the current page URL with the `ask` query parameter: ``` GET https://px4.gitbook.io/px4-user-guide/assembly/quick_start_pixhawk4.md?ask= ``` The question should be specific, self-contained, and written in natural language. The response will contain a direct answer to the question and relevant excerpts and sources from the documentation. Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.