Magnetometer

ak09916

Source: drivers/magnetometer/akm/ak09916

Usage

ak09916 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 12
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

ak8963

Source: drivers/magnetometer/akm/ak8963

Usage

ak8963 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 12
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

bmm150

Source: drivers/magnetometer/bosch/bmm150

Usage

bmm150 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 16
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

hmc5883

Source: drivers/magnetometer/hmc5883

Usage

hmc5883 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select pin (for internal SPI) or index (for external SPI)
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-R <val>]  Rotation
                 default: 0
     [-T]        Enable temperature compensation

   stop

   status        print status info

ist8308

Source: drivers/magnetometer/isentek/ist8308

Usage

ist8308 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 12
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

ist8310

Source: drivers/magnetometer/isentek/ist8310

Usage

ist8310 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 14
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

lis2mdl

Source: drivers/magnetometer/lis2mdl

Usage

lis2mdl <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select pin (for internal SPI) or index (for external SPI)
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 30
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

lis3mdl

Source: drivers/magnetometer/lis3mdl

Usage

lis3mdl <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select pin (for internal SPI) or index (for external SPI)
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 30
     [-R <val>]  Rotation
                 default: 0

   reset

   stop

   status        print status info

lsm9ds1_mag

Source: drivers/magnetometer/lsm9ds1_mag

Usage

lsm9ds1_mag <command> [arguments...]
 Commands:
   start
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select pin (for internal SPI) or index (for external SPI)
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

qmc5883l

Source: drivers/magnetometer/qmc5883l

Usage

qmc5883l <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 13
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

rm3100

Source: drivers/magnetometer/rm3100

Usage

rm3100 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select pin (for internal SPI) or index (for external SPI)
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info

vcm1193l

Source: drivers/magnetometer/vtrantech/vcm1193l

Usage

vcm1193l <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-R <val>]  Rotation
                 default: 0

   stop

   status        print status info