PX4 User Guide
  • Introduction
  • Getting Started
    • Basic Concepts
    • Vehicles/Frames
    • Flight Controllers
    • Sensors
    • Radio Systems
    • Flight Modes
    • Vehicle Status Notifications
      • LED Meanings
      • Tune/Sound Meanings
      • Preflight Checks
    • Payloads & Cameras
    • Flight Reporting
  • Basic Assembly
    • Mounting the Flight Controller
    • Mounting the GPS/Compass
    • Vibration Isolation
    • Cable Wiring
    • CUAV Pixhawk V6X Wiring QuickStart
    • CUAV V5+ Wiring Quickstart
    • CUAV V5 nano Wiring Quickstart
    • Holybro Pixhawk 6C Wiring Quickstart
    • Holybro Pixhawk 6X Wiring Quickstart
    • Holybro Pixhawk 5X Wiring Quickstart
    • Holybro Pixhawk 4 Wiring Quickstart - Discontinued
    • Holybro Pixhawk 4 Mini Wiring Quickstart - Discontinued
    • Holybro Durandal Wiring Quickstart
    • Holybro Pix32 v5 Wiring Quickstart
    • Cube Wiring Quickstart
    • Pixracer Wiring Quickstart
    • mRo (3DR) Pixhawk Wiring Quickstart
  • Standard Configuration
    • Firmware
    • Airframe
    • Sensor Orientation
    • Compass
    • Gyroscope
    • Accelerometer
    • Airspeed
    • Level Horizon Calibration
    • Radio Setup
    • Joystick Setup
    • Flight Modes
    • Battery
    • Safety
      • Failsafe Simulation
    • ESC Calibration
    • Actuators
    • Autotune
  • Vehicle Types & Setup
    • Multicopters
      • Multicopter Config/Tuning
        • MC Filter/Control Latency Tuning
        • MC PID Tuning (Manual/Basic)
        • MC PID Tuning Guide (Manual/Advanced)
        • MC Setpoint Tuning (Trajectory Generator)
          • MC Jerk-limited Type Trajectory
        • Multicopter Racer Setup
      • X500 v2 (Pixhawk 6C)
      • X500 v2 (Pixhawk 5X)
      • X500 (Pixhawk 4)
      • S500 V2 (Pixhawk 4)
      • DJI F450 (CUAV v5+)
      • DJI F450 (CUAV v5 nano)
      • QAV250 (Pixhawk4 Mini) - Discontinued
      • DJI F450 + RTK (Pixhawk 3 Pro)
      • QAV250 (Pixhawk Mini)
      • QAV-R 5" Racer (Pixracer)
      • Omnicopter
    • Planes
      • Fixed Wing Config/Tuning
        • Fixedwing PID Tuning Guide
        • Fixedwing Advanced Tuning Guide
        • Fixedwing Trimming Guide
      • Reptile Dragon 2 (ARK6X)
      • Turbo Timber Evolution (Pixhawk 4 Mini)
      • Wing Wing Z84 (Pixracer)
    • VTOL
      • VTOL Config/Tuning
        • QuadPlane Configuration
        • Back-transition Tuning
        • VTOL w/o Airspeed Sensor
        • VTOL Weather Vane
      • Standard VTOL
        • FunCub QuadPlane (Pixhawk)
        • Ranger QuadPlane (Pixhawk)
        • Falcon Vertigo QuadPlane (Dropix)
      • Tailsitter VTOL
        • Build: TBS Caipiroshka Tailsitter Build (Pixracer)
      • Tiltrotor VTOL
        • Build: Convergence Tiltrotor (Pixfalcon)
    • Airships (experimental)
    • Autogyros (experimental)
      • ThunderFly Auto-G2 (Holybro pix32)
    • Balloons (experimental)
    • Helicopter (experimental)
      • Helicopter Config/Tuning
    • Rovers (experimental)
      • Traxxas Stampede
    • Submarines (experimental)
      • BlueROV2
    • Airframes Reference
  • Flying
    • First Flight Guidelines
    • Flying 101
    • Missions
      • Package Delivery Mission
    • GeoFence
    • Safety Point Planning
    • Flight Modes
      • Position Mode (MC)
      • Altitude Mode (MC)
      • Manual/Stabilized Mode (MC)
      • Acro Mode (MC)
      • Orbit Mode (MC)
      • Position Mode (FW)
      • Altitude Mode (FW)
      • Stabilized Mode (FW)
      • Acro Mode (FW)
      • Manual Mode (FW)
      • Takeoff Mode
      • Land Mode
      • Return Mode
      • Hold Mode
      • Mission Mode
      • Follow Me Mode
      • Offboard Mode
    • Terrain Following/Holding
  • Flight Log Analysis
    • Log Analysis using Flight Review
    • Log Analysis using PlotJuggler
  • Advanced Configuration
    • Finding/Updating Parameters
    • Full Parameter Reference
    • ECL/EKF Overview & Tuning
    • Flight Termination Configuration
    • Bootloader Flashing onto Betaflight Systems
    • Land Detector Configuration
    • Prearm/Arm/Disarm Configuration
    • IMU Factory Calibration
    • Sensor Thermal Compensation
    • Compass Power Compensation
    • Advanced Controller Orientation
    • Static Pressure Buildup
    • Serial Port Configuration
    • MAVLink Telemetry (OSD/GCS)
    • PX4 Ethernet Setup
    • Bootloader Update
  • Hardware (Drones&Parts)
    • Complete Vehicles
      • ModalAI Starling
      • PX4 Vision Kit
      • MindRacer BNF & RTF
        • MindRacer 210
        • NanoMind 110
      • Holybro Kopis 2
      • Bitcraze Crazyflie 2.1
    • Flight Controllers (Autopilots)
      • Pixhawk Series
        • Silicon Errata
      • Pixhawk Standard Autopilots
        • CUAV Pixhawk V6X (FMUv6X)
        • Holybro Pixhawk 6X (FMUv6X)
        • Holybro Pixhawk 6C (FMUv6C)
        • Holybro Pixhawk 6C Mini(FMUv6C)
        • Holybro Pix32 v6 (FMUv6C)
        • Holybro Pixhawk 5X (FMUv5X)
        • Holybro Pixhawk 4 (FMUv5) - Discontinued
        • Holybro Pixhawk 4 Mini (FMUv5) - Discontinued
        • Drotek Pixhawk 3 Pro (FMUv4pro)
        • mRo Pixracer (FMUv4)
        • Hex Cube Black (FMUv3)
        • mRo Pixhawk (FMUv3)
        • Holybro Pixhawk Mini (FMUv3) - Discontinued
      • Manufacturer-Supported Autopilots
        • AirMind MindPX
        • AirMind MindRacer
        • ARK Electronics ARKV6X
        • CUAV X7
        • CUAV Nora
        • CUAV V5+ (FMUv5)
        • CUAV V5 nano (FMUv5)
        • CUAV Pixhack v3 (FMUv3)
        • CubePilot Cube Orange+ (CubePilot)
        • CubePilot Cube Orange (CubePilot)
        • CubePilot Cube Yellow (CubePilot)
        • Holybro Kakute H7v2
        • Holybro Kakute H7mini
        • Holybro Kakute H7
        • Holybro Durandal
        • Holybro Pix32 v5
        • ModalAI Flight Core v1
        • ModalAI VOXL Flight
        • ModalAI VOXL 2
        • mRobotics-X2.1 (FMUv2)
        • mRo Control Zero F7)
        • NXP RDDRONE-FMUK66 FMU
        • Sky-Drones AIRLink
        • SPRacing SPRacingH7EXTREME
        • ThePeach FCC-K1
        • ThePeach FCC-R1
      • Experimental Autopilots
        • BeagleBone Blue
        • Raspberry Pi 2/3 Navio2
        • Raspberry Pi 2/3/4 PilotPi
          • PilotPi with Raspberry Pi OS
          • PilotPi with Ubuntu Server
      • Discontinued Autopilots/Vehicles
        • Drotek Dropix (FMUv2)
        • Omnibus F4 SD
        • BetaFPV Beta75X 2S Brushless Whoop
        • Bitcraze Crazyflie 2.0
        • Aerotenna OcPoC-Zynq Mini
        • CUAV v5
        • Holybro Kakute F7 (Discontinued)
        • Holybro Pixfalcon
        • Holybro pix32 (FMUv2)
        • mRo AUAV-X2
        • 3DR Pixhawk 1
        • Snapdragon Flight
        • Intel® Aero RTF Drone (Discontinued)
      • Pixhawk Autopilot Bus (PAB) & Carriers
        • ARK Electronics Pixhawk Autopilot Bus Carrier
    • Flight Controller Peripherals
      • ADSB/FLARM (Traffic Avoidance)
      • Air Traffic Avoidance: ADSB/FLARM
      • Air Traffic Avoidance: UTM
      • Airspeed Sensors
        • TFSlot Airspeed Sensor
      • Barometers
      • Camera
      • Distance Sensors (Rangefinders)
        • Lightware SFxx Lidar
        • Ainstein US-D1 Standard Radar Altimeter
        • LeddarOne Lidar
        • Benewake TFmini Lidar
        • Lidar-Lite
        • TeraRanger
        • Lanbao PSK-CM8JL65-CC5
        • Avionics Anonymous Laser Altimeter UAVCAN Interface
      • ESCs & Motors
        • PWM ESCs and Servos
        • DShot ESCs
        • OneShot ESCs and Servos
        • DroneCAN ESCs
          • Zubax Telega
          • PX4 Sapog ESC Firmware
            • Holybro Kotleta
            • Zubax Orel
        • VESC
      • TBS Crossfire (CRSF) Telemetry
      • FrSky Telemetry
      • Gimbal (Mount) Configuration
      • GPS/Compass
        • ARK GPS
        • Holybro DroneCAN M8N GPS
        • LOCOSYS Hawk A1 GNSS
        • Hex Here2
        • Holybro M8N & M9N GPS
        • Sky-Drones SmartAP GPS
      • Grippers
        • Servo Gripper
      • Optical Flow
        • ARK Flow
        • PMW3901
        • PX4FLOW (Deprecated)
      • Precision Landing
      • Parachute
      • Power Modules/PDB
        • CUAV HV pm
        • CUAV CAN PMU
        • Holybro PM02
        • Holybro PM07
        • Holybro PM06 V2
        • Holybro PM02D (digital)
        • Holybro PM03D (digital)
        • Pomegranate Systems Power Module
        • Sky-Drones SmartAP PDB
      • Satellite Coms (Iridium/RockBlock)
      • Telemetry Radios
        • SiK Radio
          • RFD900 (SiK) Telemetry Radio
          • HolyBro (SIK) Telemetry Radio
        • Telemetry Wifi
          • ESP8266 WiFi Module
          • ESP32 WiFi Module
          • 3DR Telemetry Wifi (Discontinued)
        • Microhard Serial Telemetry Radio
          • ARK Electron Microhard Serial Telemetry Radio
          • Holybro Microhard P900 Telemetry Radio
        • CUAV P8 Telemetry Radio
        • HolyBro XBP9X - Discontinued
      • RTK GPS
        • ARK RTK GPS
        • RTK GPS Heading with Dual u-blox F9P
        • CUAV C-RTK
        • CUAV C-RTK2 PPK/RTK GNSS
        • CUAV C-RTK 9Ps
        • Femtones MINI2 Receiver
        • Freefly RTK GPS
        • Holybro H-RTK-F9P
        • Holybro H-RTK-M8P
        • Holybro H-RTK Unicore UM982 GPS
        • Locosys Hawk R1
        • Locosys Hawk R2
        • Septentrio AsteRx-RIB
        • Septentrio mosaic-go
        • Trimble MB-Two
        • CubePilot Here+ (Discontined)
      • Remote ID
      • Smart Batteries
        • Rotoye Batmon Battery Smartification Kit
      • Tachometers (Revolution Counters)
        • ThunderFly TFRPM01 Tachometer Sensor
      • I2C Peripherals
        • I2C bus accelerators
        • TFI2CADT01 I2C address translator
      • CAN Peripherals
      • DroneCAN Peripherals
        • PX4 DroneCAN Firmware
        • ARK CANnode
    • Companion Computers
      • Pixhawk + Companion Setup
        • RasPi Pixhawk Companion
      • Companion Computer Peripherals
      • Holybro Pixhawk RPI CM4 Baseboard
      • Auterion Skynode
      • Computer Vision
        • Obstacle Avoidance
        • Safe Landing
        • Collision Prevention
        • Path Planning Interface
        • Motion Capture (MoCap)
        • Visual Inertial Odometry (VIO)
          • Realsense T265 Tracking Camera (VIO)
      • Video Streaming
  • Development
    • Getting Started
      • Recommended Hardware/Setup
      • Toolchain Installation
        • MacOS Setup
        • Ubuntu Setup
        • Windows Setup
        • Visual Studio Code IDE
        • Other/Generic Tools
      • Building the Code
      • Writing your First Application
      • Application/Module Template
    • Concepts
      • PX4 Architecture
      • PX4 Flight Stack Architecture
        • Controller Diagrams
      • Events Interface
      • Flight Modes
      • Flight Tasks
      • Control Allocation
      • PWM limit state machine
      • System Startup
      • SD Card Layout
    • Simulation
      • jMAVSim Simulation
        • Multi-Vehicle Sim with JMAVSim
      • Gazebo Simulation
        • Vehicles
        • Multi-Vehicle Sim
      • Gazebo Classic Simulation
        • Vehicles
        • Worlds
        • Multi-Vehicle Sim
      • FlightGear Simulation
        • FlightGear Vehicles
        • Multi-Vehicle Sim with FlightGear
      • JSBSim Simulation
      • AirSim Simulation
      • Multi-Vehicle Simulation
      • Simulate Failsafes
      • HITL Simulation
      • Simulation-In-Hardware
    • Hardware
      • Flight Controller Reference Design
      • Manufacturer’s Board Support Guide
      • Flight Controller Porting Guide
        • PX4 Board Configuration (kconfig)
        • NuttX Board Porting Guide
      • Serial Port Mapping
      • Airframes
        • Adding a New Airframe
      • Device Drivers
      • Telemetry Radio
        • SiK Radio
      • Sensor and Actuator I/O
        • DroneCAN
        • I2C Bus
        • UART/Serial Ports
          • Port-Configurable Serial Drivers
      • RTK GPS (Integration)
    • Middleware
      • uORB Messaging
      • uORB Graph
      • uORB Message Reference
        • ActionRequest
        • ActuatorArmed
        • ActuatorControlsStatus
        • ActuatorMotors
        • ActuatorOutputs
        • ActuatorServos
        • ActuatorServosTrim
        • ActuatorTest
        • AdcReport
        • Airspeed
        • AirspeedValidated
        • AirspeedWind
        • AutotuneAttitudeControlStatus
        • BatteryStatus
        • ButtonEvent
        • CameraCapture
        • CameraStatus
        • CameraTrigger
        • CellularStatus
        • CollisionConstraints
        • CollisionReport
        • ControlAllocatorStatus
        • Cpuload
        • DebugArray
        • DebugKeyValue
        • DebugValue
        • DebugVect
        • DifferentialPressure
        • DistanceSensor
        • Ekf2Timestamps
        • EscReport
        • EscStatus
        • EstimatorAidSource1d
        • EstimatorAidSource2d
        • EstimatorAidSource3d
        • EstimatorBias
        • EstimatorBias3d
        • EstimatorEventFlags
        • EstimatorGpsStatus
        • EstimatorInnovations
        • EstimatorSelectorStatus
        • EstimatorSensorBias
        • EstimatorStates
        • EstimatorStatus
        • EstimatorStatusFlags
        • Event
        • FailsafeFlags
        • FailureDetectorStatus
        • FollowTarget
        • FollowTargetEstimator
        • FollowTargetStatus
        • GeneratorStatus
        • GeofenceResult
        • GimbalControls
        • GimbalDeviceAttitudeStatus
        • GimbalDeviceInformation
        • GimbalDeviceSetAttitude
        • GimbalManagerInformation
        • GimbalManagerSetAttitude
        • GimbalManagerSetManualControl
        • GimbalManagerStatus
        • GpioConfig
        • GpioIn
        • GpioOut
        • GpioRequest
        • GpsDump
        • GpsInjectData
        • Gripper
        • HealthReport
        • HeaterStatus
        • HomePosition
        • HoverThrustEstimate
        • InputRc
        • InternalCombustionEngineStatus
        • IridiumsbdStatus
        • IrlockReport
        • LandingGear
        • LandingGearWheel
        • LandingTargetInnovations
        • LandingTargetPose
        • LaunchDetectionStatus
        • LedControl
        • LogMessage
        • LoggerStatus
        • MagWorkerData
        • MagnetometerBiasEstimate
        • ManualControlSetpoint
        • ManualControlSwitches
        • MavlinkLog
        • MavlinkTunnel
        • Mission
        • MissionResult
        • ModeCompleted
        • MountOrientation
        • NavigatorMissionItem
        • NormalizedUnsignedSetpoint
        • NpfgStatus
        • ObstacleDistance
        • OffboardControlMode
        • OnboardComputerStatus
        • OrbTest
        • OrbTestLarge
        • OrbTestMedium
        • OrbitStatus
        • ParameterUpdate
        • Ping
        • PositionControllerLandingStatus
        • PositionControllerStatus
        • PositionSetpoint
        • PositionSetpointTriplet
        • PowerButtonState
        • PowerMonitor
        • PpsCapture
        • PwmInput
        • Px4ioStatus
        • QshellReq
        • QshellRetval
        • RadioStatus
        • RateCtrlStatus
        • RcChannels
        • RcParameterMap
        • Rpm
        • RtlTimeEstimate
        • SatelliteInfo
        • SensorAccel
        • SensorAccelFifo
        • SensorBaro
        • SensorCombined
        • SensorCorrection
        • SensorGnssRelative
        • SensorGps
        • SensorGyro
        • SensorGyroFft
        • SensorGyroFifo
        • SensorHygrometer
        • SensorMag
        • SensorOpticalFlow
        • SensorPreflightMag
        • SensorUwb
        • SensorSelection
        • SensorsStatus
        • SensorsStatusImu
        • SystemPower
        • TakeoffStatus
        • TaskStackInfo
        • TecsStatus
        • TelemetryStatus
        • TiltrotorExtraControls
        • TimesyncStatus
        • TrajectoryBezier
        • TrajectorySetpoint
        • TrajectoryWaypoint
        • TransponderReport
        • TuneControl
        • UavcanParameterRequest
        • UavcanParameterValue
        • UlogStream
        • UlogStreamAck
        • UwbDistance
        • UwbGrid
        • VehicleAcceleration
        • VehicleAirData
        • VehicleAngularAccelerationSetpoint
        • VehicleAngularVelocity
        • VehicleAttitude
        • VehicleAttitudeSetpoint
        • VehicleCommand
        • VehicleCommandAck
        • VehicleConstraints
        • VehicleControlMode
        • VehicleGlobalPosition
        • VehicleImu
        • VehicleImuStatus
        • VehicleLandDetected
        • VehicleLocalPosition
        • VehicleLocalPositionSetpoint
        • VehicleMagnetometer
        • VehicleOdometry
        • VehicleOpticalFlow
        • VehicleOpticalFlowVel
        • VehicleRatesSetpoint
        • VehicleRoi
        • VehicleStatus
        • VehicleThrustSetpoint
        • VehicleTorqueSetpoint
        • VehicleTrajectoryBezier
        • VehicleTrajectoryWaypoint
        • VtolVehicleStatus
        • Wind
        • YawEstimatorStatus
      • MAVLink Messaging
      • uXRCE-DDS (PX4-ROS 2/DDS Bridge)
    • Modules & Commands
      • Autotune
      • Commands
      • Communication
      • Controllers
      • Drivers
        • Airspeed Sensor
        • Baro
        • Distance Sensor
        • IMU
        • INS
        • Magnetometer
        • Optical Flow
        • Rpm Sensor
        • Transponder
      • Estimators
      • Simulations
      • System
      • Template
    • Debugging/Logging
      • FAQ
      • Consoles/Shells
        • MAVLink Shell
        • System Console
      • Debugging with GDB
        • SWD Debug Port
        • JLink Probe
        • Black Magic/DroneCode Probe
        • STLink Probe
        • Hardfault Debugging
      • Debugging with Eclipse
      • Failure Injection
      • Sensor/Topic Debugging
      • Simulation Debugging
      • Sending Debug Values
      • System-wide Replay
      • Profiling
      • Binary Size Profiling
      • Logging
      • Flight Log Analysis
      • ULog File Format
    • Tutorials
      • Long-distance Video Streaming
      • Connecting an RC Receiver on Linux
    • Advanced Topics
      • Parameters & Configs
      • Package Delivery Architecture
      • Computer Vision
        • Motion Capture (VICON, Optitrack, NOKOV)
      • Installing driver for Intel RealSense R200
      • Switching State Estimators
      • Out-of-Tree Modules
      • STM32 Bootloader
      • System Tunes
      • Advanced Linux Installation Cases
      • Windows Cygwin Toolchain Maintenance
      • Unsupported Developer Setup
        • CentOS Linux
        • Arch Linux
        • Windows VM Toolchain
        • Windows Cygwin Toolchain
        • Qt Creator IDE
    • Platform Testing and CI
      • Test Flights
        • Test MC_01 - Manual Modes
        • Test MC_02 - Full Autonomous
        • Test MC_03 - Auto Manual Mix
        • Test MC_04 - Failsafe Testing
        • Test MC_05 - Indoor Flight (Manual Modes)
      • Unit Tests
      • Continuous Integration
      • MAVSDK Integration Testing
      • ROS Integration Testing
      • Docker Containers
      • Maintenance
  • Drone Apps & APIs
    • Offboard Control from Linux
    • ROS
      • ROS 2
        • ROS 2 User Guide
        • ROS 2 Offboard Control Example
        • ROS 2 Multi Vehicle Simulation
      • ROS 1 with MAVROS
        • ROS/MAVROS Installation Guide
        • ROS/MAVROS Offboard Example (C++)
        • ROS/MAVROS Offboard Example (Python)
        • ROS/MAVROS Sending Custom Messages
        • ROS/MAVROS with Gazebo Classic Simulation
        • Gazebo Classic OctoMap Models with ROS 1
        • ROS/MAVROS Installation on RPi
        • External Position Estimation (Vision/Motion based)
    • DroneKit
  • Contribution (&Dev Call)
    • Dev Call
    • Support
    • Source Code Management
      • GIT Examples
    • Documentation
    • Translation
    • Terminology/Notation
    • Licenses
  • Releases
    • 1.14
    • 1.13
    • 1.12
Powered by GitBook
On this page
  • Accessories
  • Wiring Overview
  • Mount and Orient Controller
  • GPS + Compass + Safety Switch + LED
  • Safety Switch
  • Buzzer
  • Radio Control
  • PPM-SUM / Futaba S.Bus receivers
  • Spektrum Satellite Receivers
  • PWM Receivers
  • Power
  • Telemetry System (Optional)
  • SD Card (Optional)
  • Motors
  • Other Peripherals
  • Configuration
  • Bootloader Updates
  • Further information
  1. Basic Assembly

Cube Wiring Quickstart

PreviousHolybro Pix32 v5 Wiring QuickstartNextPixracer Wiring Quickstart

Last updated 1 year ago

:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.

Note also that while Cube Black is fully supported by PX4, Cube Yellow and Cube Orange are Manufacturer Supported. :::

This quick start guide shows how to power the Cube® flight controllers and connect their most important peripherals.

:::tip The instructions apply to all Cube variants, including Cube Black, Cube Yellow and Cube Orange. Further/updated information may be available in the Cube User Manual (Cube Docs). :::

Accessories

The exception is that some kits do not include a GPS, which will have to be purchased separately (see below).

Wiring Overview

The image below shows how to connect the most important sensors and peripherals. We'll go through each of these in detail in the following sections.

  1. Telemetry System — Allows you to plan/run missions, and control and monitor the vehicle in real time. Typically includes telemetry radios, tablet/PC and ground station software.

  2. Buzzer — Provides audio signals that indicate what the UAV is doing

  3. Remote Control Receiver System — Connects to a hand-held transmitter that an operator can use to manually fly the vehicle (shown is a PWM receiver with PWM->PPM converter).

  4. (Dedicated) Safety switch — Press and hold to lock and unlock motors. Only required if you are not using the recommended GPS with inbuilt safety switch.

  5. GPS, Compass, LED, Safety Switch — The recommended GPS module contains GPS, Compass, LED and Safety Switch.

  6. Power System — Powers Cube and the motor ESCs. Consists of LiPo battery, power module, and optional battery warning system (audio warning if battery power goes below a predefined level).

:::note The port labeled GPS2 maps to TEL4 in PX4 (i.e. if connecting to the port labeled GPS2, assign the serial port configuration parameter for the connected hardware to TEL4). :::

Mount and Orient Controller

Mount the Cube as close as possible to your vehicle’s center of gravity, ideally oriented top-side up and with the arrow pointing towards the front of the vehicle (note the subtle arrow marker on top of the cube)

:::note If the controller cannot be mounted in the recommended/default orientation (e.g. due to space constraints) you will need to configure the autopilot software with the orientation that you actually used: Flight Controller Orientation. :::

The Cube can be mounted using either vibration-damping foam pads (included in the kit) or mounting screws. The mounting screws in the Cube accessories are designed for a 1.8mm thick frameboard. Customized screws are supposed to be M2.5 with thread length inside Cube in range 6mm~7.55mm.

GPS + Compass + Safety Switch + LED

The recommended GPS modules are the Here and Here+, both of which incorporate a GPS module, Compass, Safety Switch and LEDs. The difference between the modules is that Here+ supports centimeter level positioning via RTK. Otherwise they are used/connected in the same way.

:::warning The Here+ has been superseded by the Here3 a DroneCAN RTK-GNSS that incorporate a compass and LEDs (but no safety switch). See DroneCAN for Here3 wiring and PX4 configuration information. :::

The module should be mounted on the frame as far away from other electronics as possible, with the direction marker towards the front of the vehicle (separating the compass from other electronics will reduce interference). It must be connected to the GPS1 port using the supplied 8-pin cable.

The diagram below shows a schematic view of the module and its connections.

:::note The GPS module's integrated safety switch is enabled by default (when enabled, PX4 will not let you arm the vehicle). To disable the safety press and hold the safety switch for 1 second. You can press the safety switch again to enable safety and disarm the vehicle (this can be useful if, for whatever reason, you are unable to disarm the vehicle from your remote control or ground station). :::

:::tip If you want to use an old-style 6-pin GPS module, the kit comes with a cable that you can use to connect both the GPS and Safety Switch. :::

Safety Switch

The dedicated safety switch that comes with the Cube is only required if you are not using the recommended GPS (which has an inbuilt safety switch).

If you are flying without the GPS you must attach the switch directly to the GPS1 port in order to be able to arm the vehicle and fly (or via a supplied cable if using an old-style 6-pin GPS).

Buzzer

The buzzer plays tones and tunes that provide audible notification of vehicle status (including tones that are helpful for debugging startup issues, and that notify of conditions that might affect safe operation of the vehicle).

The buzzer should be connected to the USB port as shown (no further configuration is required).

Radio Control

A remote control (RC) radio system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).

You will need to select a compatible transmitter/receiver and then bind them so that they communicate (read the instructions that come with your specific transmitter/receiver).

The instructions below show how to connect the different types of receivers.

PPM-SUM / Futaba S.Bus receivers

Connect the ground(-),power(+),and signal(S) wires to the RC pins using the provided 3-wire servo cable.

Spektrum Satellite Receivers

Spektrum DSM, DSM2, and DSM-X Satellite RC receivers connect to the SPKT/DSM port.

PWM Receivers

The Cube cannot directly connect to PPM or PWM receivers that have an individual wire for each channel. PWM receivers must therefore connect to the RCIN port via a PPM encoder module, which may be purchased from hex.aero or proficnc.com.

Power

Cube is typically powered from a Lithium Ion Polymer (LiPo) Battery via a Power Module (supplied with the kit) that is connected to the POWER1 port. The power module provides reliable supply and voltage/current indication to the board, and may separately supply power to ESCs that are used to drive motors on a multicopter vehicle.

A typical power setup for a Multicopter vehicle is shown below.

:::Note The power (+) rail of MAIN/AUX is not powered by the power module supply to the flight controller. In order to drive servos for rudders, elevons, etc., it will need to be separately powered.

This can be done by connecting the power rail to a BEC equipped ESC, a standalone 5V BEC, or a 2S LiPo battery. Ensure the voltage of servo you are going to use is appropriate! :::

Telemetry System (Optional)

A telemetry system allows you to communicate with, monitor, and control a vehicle in flight from a ground station (for example, you can direct the UAV to a particular position, or upload a new mission).

The communication channel is via Telemetry Radios. The vehicle-based radio should be connected to the TELEM1 port (if connected to this port, no further configuration is required). The other radio is connected to your ground station computer or mobile device (usually via USB).

SD Card (Optional)

SD cards are highly recommended as they are needed to log and analyse flight details, to run missions, and to use UAVCAN-bus hardware. Insert the Micro-SD card into Cube as shown (if not already present).

Motors

Motors/servos are connected to the MAIN and AUX ports in the order specified for your vehicle in the Airframe Reference.

:::note This reference lists the output port to motor/servo mapping for all supported air and ground frames (if your frame is not listed in the reference then use a "generic" airframe of the correct type). :::

:::warning The mapping is not consistent across frames (e.g. you can't rely on the throttle being on the same output for all plane frames). Make sure to use the correct mapping for your vehicle. :::

Other Peripherals

The wiring and configuration of optional/less common components is covered within the topics for individual peripherals.

:::note If connecting peripherals to the port labeled GPS2, assign the PX4 serial port configuration parameter for the hardware to TEL4 (not GPS2). :::

Configuration

Configuration is performed using QGroundContro.

After downloading, installing and running QGroundControl, connect the board to your computer as shown.

Basic/common configuration information is covered in: Autopilot Configuration.

QuadPlane specific configuration is covered here: QuadPlane VTOL Configuration

Bootloader Updates

If you get the [Program PX4IO(../getting_started/tunes.md#program-px4io) warning tone after flashing PX4 firmware, you may need to update the bootloader.

The safety switch can be used to force bootloader updates. To use this feature de-power the Cube, hold down the safety switch, then power the Cube over USB.

Further information

  • Cube Black

  • Cube Yellow

  • Cube Orange

  • Cube Docs (Manufacturer):

    • Cube Module Overview

    • Cube User Manual

    • Mini Carrier Board

Cube comes with most (or all) of the accessories you will need when .

:::tip More information about available ports can be found here: . :::

:::tip For more information see . :::

Basic Concepts > SD Cards (Removable Memory)
Cube Accessories
Cube - Wiring Overview
Cube Mount - Direction of Front
Cube Mount - Mounting Plate
Here+ Connector Diagram
Cube Buzzer
Cube - RCIN
Cube - Spektrum
Power Setup - MC
Telemetry Radio
Cube - Mount SDCard
Cube - Motor Connections
Cube - USB Connection to Computer
purchased
Cube > Ports