Holybro Pixhawk 6C (FMUv6C)
Last updated
Last updated
:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::
Pixhawk 6C® is the latest update to the successful family of Pixhawk® flight controllers designed and made in collaboration with Holybro® and the PX4 team.
It is equipped with a high performance H7 Processor, and comes with IMU redundancy, temperature-controlled IMU board, and cost effective design, delivering incredible performance and reliability. It complies with the Pixhawk Connector Standard.
:::tip This autopilot is supported by the PX4 maintenance and test teams. :::
The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers.
Inside the Pixhawk® 6C, you can find an STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pixhawk® 6C's H7 microcontroller contain the Arm® Cortex®-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models.
The Pixhawk 6C includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.
The Pixhawk® 6C is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial application.
Key Design Points
High performance STM32H743 Processor with more computing power & RAM
New cost-effective design with low-profile form factor
Newly designed integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs
FMU Processor: STM32H743
32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM
IO Processor: STM32F103
32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
On-board sensors
Accel/Gyro: ICM-42688-P
Accel/Gyro: BMI055
Mag: IST8310
Barometer: MS5611
Voltage Ratings:
Max input voltage: 6V
USB Power Input: 4.75~5.25V
Servo Rail Input: 0~36V
Current Ratings:
TELEM1 Max output current limiter: 1.5A
All other port combined output current limiter: 1.5A
Dimensions: 84.8 * 44 * 12.4 mm
Weight: 59.3g
16- PWM servo outputs (8 from IO, 8 from FMU)
3 general purpose serial ports
TELEM1 - Full flow control, separate 1.5A current limit
TELEM2 - Full flow control
TELEM3
2 GPS ports
GPS1 - Full GPS port (GPS plus safety switch)
GPS2 - Basic GPS port
1 I2C port
Supports dedicated I2C calibration EEPROM located on sensor module
2 CAN Buses
CAN Bus has individual silent controls or ESC RX-MUX control
2 Debug ports:
FMU Debug
I/O Debug
Dedicated R/C input for Spektrum / DSM and S.BUS, CPPM, analog / PWM RSSI
Dedicated S.BUS output
2 Power input ports (Analog)
Other Characteristics:
Operating & storage temperature: -40 ~ 85°c
Order from Holybro.
The Pixhawk 6C Wiring Quick Start provides instructions on how to assemble required/important peripherals including GPS, Power Module etc.
USART1
/dev/ttyS0
GPS1
USART2
/dev/ttyS1
TELEM3
USART3
/dev/ttyS2
Debug Console
UART5
/dev/ttyS3
TELEM2
USART6
/dev/ttyS4
PX4IO
UART7
/dev/ttyS5
TELEM1
UART8
/dev/ttyS6
GPS2
Pixhawk 6C can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: POWER1, POWER2 and USB.
Normal Operation Maximum Ratings
Under these conditions all power sources will be used in this order to power the system:
POWER1 and POWER2 inputs (4.9V to 5.5V)
USB input (4.75V to 5.25V)
Absolute Maximum Ratings
Under these conditions the system will not draw any power (will not be operational), but will remain intact.
POWER1 and POWER2 inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
USB input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
Servo input: VDD_SERVO pin of FMU PWM OUT and I/O PWM OUT (0V to 42V undamaged)
Voltage monitoring
Pixhawk 6C uses analog power modules.
Holybro makes various analog power modules for different needs:
:::tip Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected. :::
To build PX4 for this target:
The PX4 System Console and SWD interface run on the FMU Debug port.
The pinouts and connector comply with the Pixhawk Debug Full interface defined in the Pixhawk Connector Standard interface (JST SM10B connector).
1 (red)
Vtref
+3.3V
2 (blk)
Console TX (OUT)
+3.3V
3 (blk)
Console RX (IN)
+3.3V
4 (blk)
SWDIO
+3.3V
5 (blk)
SWCLK
+3.3V
6 (blk)
SWO
+3.3V
7 (blk)
NFC GPIO
+3.3V
8 (blk)
PH11
+3.3V
9 (blk)
nRST
+3.3V
10 (blk)
GND
GND
For information about using this port see:
PX4 System Console (Note, the FMU console maps to USART3).
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos. The complete set of supported configurations can be seen in the Airframes Reference.
Holybro Docs (Holybro)
