Raspberry Pi 2/3/4 PilotPi
Last updated
Last updated
:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::
:::warning PX4 support for this flight controller is experimental. :::
The PilotPi shield is a fully functional solution to run PX4 autopilot directly on Raspberry Pi. It is designed to be a low-cost but highly scalability platform with continuous updates from both Linux and PX4 sides. No proprietary driver is required, as all components have upstream support from RPi and PX4 community. PCB and schematic are open source as well.
Supported RPi boards:
Raspberry Pi 2B/3B/3B+/4B
Supported OS:
Raspberry Pi OS
Ubuntu Server (armhf/arm64)
Accelerometer / Gyro:
ICM42688P
Magnetometer:
IST8310
Barometer:
MS5611
PWM:
PCA9685
ADC:
ADS1115
Power:
3~6S battery with built-in voltage sensing.
Power the Pi through USB cable
Availability: preparing for shipping
Shield provides:
16x PWM outputting channels
GPS connector
Telemetry connector
External I2C bus connector (Note: conflicts with CSI camera)
RC input port (SBUS)
3x ADC channels range 0~5V
2*8 2.54mm unused GPIO connector
Direct accessible from RPi:
4x USB connector
CSI connector(Note: conflict with external I2C bus)
etc.
:::warning It still uses old GH1.25 connectors. Wiring is compatible with Pixhawk 2.4.8 :::
Mapped to /dev/ttySC0
1
VCC
+5V
2
TX
+3v3
3
RX
+3v3
4
NC
+3v3
5
NC
+3v3
6
GND
GND
Mapped to /dev/ttySC1
1
VCC
+5V
2
TX
+3v3
3
RX
+3v3
4
CTS
+3v3
5
RTS
+3v3
6
GND
GND
Mapped to /dev/i2c-0
1
VCC
+5V
2
SCL
+3v3(pullups)
3
SDA
+3v3(pullups)
4
GND
GND
RC is mapped to /dev/ttyAMA0 with signal inverter switch on RX line.
1
RC
+3V3~+5V
2
VCC
+5V
3
GND
GND
ADC1 is internally connected to voltage divider for battery voltage monitoring.
ADC2 is left unused.
ADC3 can be connected to an analog airspeed sensor.
ADC4 has a jumper cap between ADC and VCC, to monitor system voltage level.
1
ADCx
0V~+5V
2
VCC
+5V
3
GND
GND
:::note ADC3 & 4 have an alternative VCC source When 'Vref' switch is on, 'VCC' pin is driven by REF5050. :::
1
3V3
3v3
3V3
2
5V
5V
5V
3
4
7
7
4
14
15
8
5
17
0
11
6
27
2
13
7
22
3
15
8
23
4
16
9
7
11
26
10
5
21
29
11
6
22
31
12
12
26
32
13
13
23
33
14
16
27
36
15
26
25
37
16
GND
GND
GND
This switch will decide the signal polarity of RX line: UART_RX = SW xor RC_INPUT
On: suitable with SBUS (signal inverted)
Off: preserved
ADC 3 & 4 will have VCC driven by:
Vref output from REF5050 if on
5V pin directly from RPi if off
This switch is connected to Pin22(BCM25). System rc script will check its value and decide whether PX4 should start alongside with system booting or not.
On: start PX4 automatically
Off: don' t start PX4
Refer to specific instructions for the OS running on your RPi:
