AirMind MindPX

:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::

The AirMind® MindPX series is a new generation autopilot system branched from Pixhawk®.

MindPX Controller

:::note These flight controllers are manufacturer supported. :::

Quick Summary

:::note The main hardware documentation is here. :::

MindPX is a new generation autopilot system branched from Pixhawk®, been revised in schematic and structure, and been further enhanced with new features to make un-manned vehicle more smart and more friendly to use.

MindPX increases total PWM output channels to 16 (8 main outputs + 8 aux outputs). This means that MindPX can support more complicated VTOL configurations and more fine control. It is especially meaningful for those FMU-V4 based flight controllers as MindPX implements main and aux output in one single FMU.

• Main System-on-Chip: STM32F427

  • CPU: 32bits, 168 MHz ARM Cortex® M4 with FPU

  • RAM: 256 KB SRAM

  • 2MB Flash

  • ST Micro LSM303D 14 bit accelerometer/magnetometer

  • MEAS MS5611 barometer

  • InvenSense® MPU6500 integrated 6-axis sensors

• Highlighted features:

  • CNC processed aluminum alloy case, light and solid

  • Built-in isolated IMU redundancy

  • Total 16 PWM output channel (8 main + 8 aux)

  • 1 extra I2C port for flow connection.

  • 1 extra USB port for companion computer connection (built-in UART-to-USB converter)

  • Exposed debug port for development

Quick Start

Mounting

MindPX Mounting

Wiring

MindPX Wiring 1

MindPX Wiring 2

Pin

MindPX Pinout

Num.	Description	Num.	Description
1	Power	9	I2C2 (MindFLow)
2	Debug (refresh bootloader)	10	USB2 (Serial 2 to USB)
3	USB1 (refresh firmware)	11	UART4,5
4	Reset	12	UART1 (Telemetry)
5	UART3 (GPS)	13	CAN
6	I2C1(external compass)	14	ADC
7	TF card slot	15	Tricolor Light
8	NRF/SPI(Remote Control)	16	Looper

Radio Receiver

MindPX supports a wide variety of radio receivers (since V2.6) including: PPM/SBUS/DSM/DSM2/DSMX. MindPX also support FrSky® bi-direction telemetry D and S.Port.

For detailed Pin diagram, please refer to the User Guide.

Building Firmware

:::tip Most users will not need to build this firmware! It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected. :::

To build PX4 for this target:

make airmind_mindpx-v2_default

Companion PC connection

MindPX has a USB-TO-UART Bridge IC on the board. A micro-USB to USB type A cable is used for the connection. Connect micro-USB end to the 'OBC' port of MindPX and USB type A end to companion computer.

And the max BAUD rate is the same with px4 family, which is up to 921600.

User Guide

:::note The user guide is here. :::

Where to Buy

MindRacer is available at AirMind Store on internet. You can also find MindRacer at Amazon® or eBay®.

Serial Port Mapping

UART	Device	Port
USART1	/dev/ttyS0	RC
USART2	/dev/ttyS1	TELEM1
USART3	/dev/ttyS2	TELEM2
UART4	/dev/ttyS3	GPS1
USART6	/dev/ttyS4	?
UART7	/dev/ttyS5	Debug Console
UART8	/dev/ttyS6	?

Support

Please visit http://www.mindpx.org for more information. Or you can send email to [e-mail] for any inquiries or help.